丁香综合五月-丁香综合在线-顶级欧美色妇xxxxx-东北普通话清晰对白-免费国产小视频-免费国产小视频在线观看

CN EN
Company News
Home > Company News

The relationship between blanking gap and shear quality

Source:Suzhou Meiyuan Ruite Precision Machinery Co., Ltd. Time:2022-06-16 Browse:3811


Whether the blanking gap in the blanking process is reasonable will determine whether the upper and lower cracks on the fracture surface overlap, whether the shear force is balanced, and the size of the burr. Therefore, the mold design, manufacture and installation must ensure that the gap is uniform, and the gap between the convex and concave molds in the same manufacturing process should be kept within a reasonable range. Otherwise, the mold will appear part of the gap is too large and too small quality phenomenon.​​
 
Effect of Gap on Section Quality
1. Reasonable blanking gap
When the convex and concave gaps are appropriate, the cracks generated near the edges of the convex and concave die along the direction of the maximum shear stress can meet during the blanking process. At this time, although the section is not perpendicular to the surface of the material, it is still relatively straight, smooth and burr Smaller, the section quality of the part is better.
 
2. Punching gap is too small
When the gap is reduced, the bending moment is small and the compressive stress component is high in the deformation zone. The cracks generated near the edge of the die enter the compressive stress zone below the punch and stop developing; the cracks generated near the edge of the punch enter the compressive stress zone on the upper surface of the die and stop developing. The upper and lower cracks do not overlap. The material between the two cracks will be sheared a second time. When the upper crack is pressed into the die, it is squeezed by the wall of the die, resulting in a second bright band, and at the same time, part of the material is extruded, forming thin and high burrs on the surface. If the gap is too small, although the slump angle is small and the arch is small, the quality of the section is also defective. If there is an interlayer in the middle of the section, the two ends are bright bands, and there are long burrs on the end face.
 
3. Punching gap is too large
When the gap increases, the tensile stress in the material increases, so that the tensile fracture occurs early, so the fracture band becomes wider; the bright band becomes narrower; the bending deformation increases, so the slump and arch also increase. When the gap is too large, due to the large bending moment and the high tensile stress component, the cracks generated near the edges of the convex and concave molds will not coincide. The slope of the fractured layer generated after separation increases, and two oblique angles α1 and α2 appear on the section of the workpiece, and the section quality is not ideal. Moreover, due to the large slump angle, the large arch, the small bright band, and the high and thick burrs, the quality of the blanking parts is reduced.
 
4. The gap is uneven
The side with a small gap presents the cross-sectional feature of an excessively small gap, and the side with a large gap presents the cross-sectional feature of an excessively large gap


主站蜘蛛池模板: free hd 性欧美 | 就去干综合 | freesexvideos性亚洲老年 | 色人阁久久 | 最近中文字幕完整在线看一 | 国产婷婷综合在线视频 | 欧美日韩性视频 | 日本亚洲天堂 | 精品国产一区二区三区四 | 婷婷伊人久久 | 亚洲国产欧美在线成人aaaa | 国产精品嫩草影院在线播放 | 91麻豆精品国产综合久久久 | 国产精品视频永久免费播放 | 亚洲欧美日本国产 | 成人午夜精品网站在线观看 | 欧美国产日韩久久久 | 色图一区 | 婷婷丁香激情五月 | 欧美18 - 19sex性 | 五月激情丁香婷婷综合第九 | 亚洲成a人v天堂网 | 亚洲欧美精品中文字幕 | 免费jizz大全 | 最好看的最新中文字幕2018免费视频 | 一级毛片高清大全免费观看 | 亚洲精品欧美日韩 | 国产福利片在线观看 | 中文字幕一区二区三区乱码 | 日本网站在线看 | 日韩一级欧美一级毛片在 | 亚洲视频欧美 | vr欧美乱强伦xxxxx | 九九黄色 | 欧美成人看片一区二区三区尤物 | 成人sq视频在线观看网站 | 伊人污| 日本一级黄色大片 | 男人午夜小视频 | 成人影院vs一区二区 | www视频在线观看天堂 |